Work stool at a low treatment station: fitting Giovanni Y08 or 6001
- 16 min reading time
A work stool for a low treatment station should fit the person, the treatment and the furniture already in the room. The useful test is whether you can move close enough to the client, keep your feet supported and make contact with the backrest without moving out of reach of the work. Compare the white Giovanni Y08 and the black cosmetic stool 6001 against your actual table or treatment chair, rather than treating the word 'ergonomic' as a promise of an outcome.
Prohaar's current Y08 listing specifies a gas-lift seat-height adjustment of approximately 49–62 cm, a swivelling rectangular seat, backrest and wheeled five-star base. The store's 6001 listing confirms a contoured seat, backrest and five-star base with plastic castors. The manufacturer's original page for exact SKU 118591 adds a gas lift, swivel function, saddle-shaped profile and the same 49–62 cm height range. Those details come from the manufacturer and are not all stated on the current Prohaar card. The 6001 dimensions of 40 × 40 × 23 cm describe its package, not the assembled stool.
1. Identify your actual working height before choosing a 'low' stool
The low part of a beauty workstation is not necessarily the top of the furniture. During foot care you may work well below the client's knees. At a manicure table, the hands rest above the tabletop, while facial treatment height changes when the treatment chair is repositioned. Measure the point at which the hands do the work, not only the height of the table or bed. That distinction prevents a common error: ordering a stool because its seat appears low in a picture when the operative area is elsewhere.
Start with a practical observation. Place the client or a suitable mock-up in the position used for the treatment. Sit on a chair whose height you can measure, approach the work area and note whether your shoulders can relax, your elbows have reasonable reach and your feet remain supported. Record the preferred floor-to-seat measurement. It is a requirement for that user and treatment, not a universal value for everybody in a salon.
When the stool is lowered but a drawer presses against your knees, the obstacle is beneath the desk. When you sit on the front edge of the seat because your hands cannot reach, the distance to the client may be wrong. In either case, replacing one stool with another of the same height range is unlikely to be the first useful adjustment. Check the positions of the treatment chair, foot section and movable furniture before interpreting your discomfort as a product defect.
2. What the Y08 and 6001 product evidence actually says
Both are currently active Prohaar products, and both provide a backrest and mobile five-star base. Their most relevant differences are seat shape and how thoroughly each characteristic is described in the store and manufacturer material. Absence of a feature from a short retail description does not prove that the feature is missing. Distinguish confirmed facts from information still needing a model-specific check.
| Criterion | Giovanni Y08 white · SKU 155729 | 6001 black · SKU 118591 |
|---|---|---|
| Seat-height range | Approximately 49–62 cm; gas lift documented by shop and maker | 49–62 cm on exact-SKU manufacturer page, not stated in current shop text |
| Seat shape | Rectangular synthetic-leather seat | Contoured seat; original maker describes a saddle profile |
| Back and mobility | Backrest, swivel, five-star wheeled base | Backrest, plastic castors, five-star base; maker also specifies swivel and gas lift |
| Dimensions caveat | Seat 40 × 41 cm; drawn base width 50 cm, not guaranteed turning clearance | 6001 drawing: seat 36 × 40 cm; ring width 30 cm. 40 × 40 × 23 cm is the box, not assembled dimensions |
| Not demonstrated | Personal fit, all backrest adjustments and floor behaviour | Personal fit, complete assembled dimensions and floor behaviour |
The current manufacturer drawing for Y08, SKU 155729, gives a 40 × 41 cm seat, a seat-height range of 49–62 cm and a drawn base width of 50 cm. Use the seat dimensions to assess space beside the thighs and the base dimension as a starting point beside chair legs or a foot support. The 50 cm is the distance between the marked endpoints in the drawing, not guaranteed turning clearance for the stool and its user. Compare these nominal dimensions with the assembled stool and allow space for feet, backrest and movement. The 6001 package size remains a separate measurement. The current manufacturer drawing for black 6001, SKU 118591, additionally gives a 36 × 40 cm seat and a padded backrest 31 cm wide and 17 cm high, with the same 49–62 cm seat-height range. Compare these nominal seat and backrest dimensions with the user; they establish neither individual pressure distribution nor the complete outer dimensions.
3. Moving closer: account for the base, knees and backrest together
Imagine a narrow pedicure station with a treatment chair close to a cabinet. When the practitioner rolls towards the foot section, the whole stool moves: its base, the user's legs and feet, and the backrest. A five-star base can encounter the foot support before the hands are sufficiently close. The solution is not to twist the torso through the treatment to bridge the distance. Measure how far the complete seated user can move forward while preserving a usable position.
At a manicure table, check the underside of the worktop, drawer casings and any integrated dust extractor. These parts determine whether your thighs fit beneath the table. A stool may be adjustable to the perfect theoretical height while the tabletop configuration forces you to remain too far away. Position the hands where the treatment takes place and observe whether you can maintain reach without constantly lifting your shoulders.
Test two distances. The first is the close working position for precision tasks. The second is a slightly withdrawn position for preparing materials, speaking with the client or changing instruments. You should be able to return to the backrest in the second position and stand up without striking furniture. A chair that can technically fit in a room when parked may still lack clearance when occupied and moved during a treatment.
4. Support the feet at the height required for the task
Foot contact is one of the clearest signs to check while fitting a stool. A practitioner may need to raise the seat to reach a client's hands or face, then discover that the heels no longer reach the floor. A backrest does not correct unsupported feet on its own. Check whether the soles can rest securely on the floor, or on a suitably stable footrest, at the working height you actually need. The Y08 shop card does not establish a footring. The current 6001 manufacturer drawing does show a ring with a drawn width of 30 cm, 15 cm above the floor. This is not the outer width of the five-star base or proof that your feet receive adequate support at the required seat height. Check the delivered configuration and personal fit; an arbitrary separate accessory does not automatically fit.
Set the height for the work, sit fully on the seat and position your feet as you naturally would during the treatment. Now turn to collect an instrument and return to the task. Does support remain under the feet, or do you slide forward to touch the floor with your toes? If the latter happens, evaluate an appropriate foot support or a change to the treatment layout. This is not an instruction to add an unverified accessory to a particular stool; compatibility and stability still need separate assessment.
The OSHA guidance for nail salons specifically highlights adjustable seating, back support and flat foot placement, with a footrest when needed. Arboportaal guidance similarly discusses supported feet and avoiding pressure from the front edge of a seat. These are broad workplace principles, not medical test results for Giovanni Y08 or 6001. They help frame your fitting observations without promising a clinical effect.
5. Backrest contact is a practical action, not a photograph
Both products have a backrest. That does not mean the user's back touches it during detailed work. People often move forward briefly to examine a nail, eyelash or toe. Ask whether the practitioner can return to an adequately supported position after each short task, without rolling so far away that the work area becomes inaccessible. This practical contact matters more than a generic statement that the stool is comfortable for long sessions.
Sit far enough onto the seat to find the backrest, keeping the fronts of the thighs free from unwanted pressure. Reach the tools and then lean back gently. If doing so requires a marked change of position or causes the feet to leave their support, some part of the arrangement is unsuitable. It could be the distance to the client, the size and angle of the treatment furniture or the stool itself. Identify which component is responsible before spending money on another seat.
The Y08 manufacturer describes a shaped backrest; the 6001 description confirms a backrest paired with the contoured seat. The checked original pages do not supply a directly comparable specification for all backrest adjustments, the distance of support from the seat or individual lumbar fit. It would be unjustified to call one stool the objectively better choice for back pain or to state that either prevents musculoskeletal disorders.
6. Rectangular seat or contoured saddle profile?
The Y08's rectangular seat may feel familiar to someone who prefers a broad seating surface and small changes in hip position. It may also bring the front edge close to the underside of a low workstation. Whether that causes a problem depends on the dimensions of the user, where the knees go and the position of the hands. The description alone does not identify the best seat for every person.
For exact model 6001, the manufacturer describes a saddle-shaped contour. That feature may change how the thighs are positioned and how easily the user approaches the client. But a shape label cannot tell us whether the pressure feels comfortable, whether it suits an individual leg length or whether the position remains practical after repeated turning. Do not mistake it for proof of a built-in footring or a specialised medical posture.
Compare the two seats in the actual working sequence, not by briefly sitting on them in an open showroom. Approach the low treatment area, settle the feet, move to another instrument and return to the starting position. Test the lowest and highest work zones actually used in your practice, rather than only the middle of the adjustment range. Observe whether you slide towards the front edge or feel pressure beneath the thighs. The question is not which seat looks more professional: it is which permits the needed movements without creating a new conflict with the workspace.
7. Castors, treatment rhythm and safe space around the chair
During pedicure you may move between the client's feet. At a manicure station you might alternate between the treatment area, a storage trolley and a lamp. A stool with castors and a swivel seat can support these position changes when the floor and furniture arrangement permit them. But the route must account for the wide parts of the base, not only the size of the cushion.
The current Y08 listing identifies a silver-toned five-star base with castors. Prohaar's 6001 page confirms a five-star base and plastic wheels, while the manufacturer's page adds a swivel mechanism. We found no controlled, directly comparable information proving identical rolling resistance, automatic braking or scratch protection for every floor. Avoid assuming those qualities from the words 'easy to move'.
8. Three purchase situations: low foot care, manicure and a shared room
Low foot-care position. Check where the client's feet really are when treatment begins. The user's knees, the chair base and the client's foot support must fit in the same small area. Even a 49 cm minimum seat height may be too high for some unusually low tasks. If that happens, compare other options in Prohaar's cosmetic-stool collection and verify each model's actual working range instead of forcing the wrong seating arrangement to fit.
Manicure beside a low table. Check clearance under the worktop, the client's hand position and the route of any dust extraction or lamp cable. The ability to move closer to the hands is as important as the chosen seat height. When the user has to reach over a drawer casing, the first useful change might be the desk arrangement, not the difference between a rectangular and a contoured seat.
Shared treatment room. Record a short fitting result for each member of staff. One person may appreciate the Y08's rectangular surface; another may find the 6001's shaped profile more natural. Both state a similar height interval in the checked manufacturer documentation, but the usable position may differ between users. A team purchase needs the fit results of more than one representative practitioner.
9. A practical decision sheet before ordering
Write down the person, the treatment, the height and shape of the existing workstation, and the measured seat range needed. Then conduct the same observations with each stool. Use this approach to avoid confusing the 6001 cardboard-box dimensions with its working dimensions, or confusing the nominal adjustment range with useful foot and back support.
- Approach: can the base, knees and backrest move into the required position without a collision?
- Feet: are the feet supported at the actual treatment height, not merely while the chair is parked?
- Back: can the user return to the backrest between tasks without losing access to the client?
- Movement: do the castors have a clear route around tables, cords and nearby equipment?
- Evidence: are the missing assembled measurements, permissible load and maintenance limits confirmed for the exact SKU if they matter to the purchase?
If an approach test fails, find out which object blocks it. If the feet hang, evaluate appropriate support or a different working height. If you cannot use the backrest, reconsider the reach to the client. A different brand or style name will not necessarily fix these geometric issues. Ask Prohaar about the exact product when a deciding dimension is not available.
The manufacturer's Giovanni Y08 page and the exact black 6001 manufacturer page provide the model-specific details used here. They are not individual medical assessments. Cross-check the current shop listings and any assembly and usage instructions before committing to the purchase.
Frequently asked questions about a stool at a low workstation
Is the Giovanni Y08 lower than the 6001?
Not according to the manufacturer pages checked for these exact models: both specify approximately 49–62 cm seat height. Prohaar directly lists this range for Y08; the corresponding 6001 range is supplied by its manufacturer's page. Whether the minimum is low enough depends on your task.
Is the 6001 actually a saddle-shaped stool?
The manufacturer's original page for SKU 118591 describes a saddle-like contour. Prohaar's present listing describes it more generally as a contoured seat. Do not transfer this description to a different 6001 variant without verifying its code.
Must I buy a separate footrest with either model?
Not automatically. It depends on seat height, leg length and working position. The manufacturer drawing shows a ring on 6001; one is not confirmed for Y08. Even with the drawn ring, check that your feet can actually rest on it securely. Assess another appropriate support or workstation arrangement if needed.
Will the backrest stop back pain during treatments?
There is no verified model-specific basis for that promise. A backrest provides a possible point of support when you can actually use it; distance to the client, seat height, foot placement and changes of posture also matter.
Does 40 × 40 × 23 cm describe the assembled 6001?
No. These are package dimensions. The assembled seat position, base width and clearance needed around the practitioner are separate measurements that should be confirmed.
Which stool should I choose for manicure or pedicure?
Neither is an objective winner without examining the workstation. Foot-care work requires clearance around the client's feet; manicure requires access beneath the table and comfortable hand reach. Test the two seat profiles in those real positions.
What if the height is right but I still cannot move closer?
Look for the obstruction: table drawer, treatment-chair arm, foot support, five-star base or backrest. Changing the furniture position may solve the problem more effectively than swapping stools with similar height ranges.
Prohaar editorial team · Product and source check: 14 October 2026. This is a furniture selection guide, not medical advice. Confirm missing assembled dimensions and the instructions for the exact model before buying.
Choose Giovanni Y08 if its rectangular seat works better with your reach and foot support. Choose black 6001 if its contoured seat gives you a more usable position. Before ordering, verify the complete assembled dimensions, the working height you need and whether you can actually make contact with the backrest beside your existing treatment furniture.